Galaxy S23 Ultra Ring Holder Kickstand Case

Why the Galaxy S23 Ultra Ring Holder Kickstand Case Is the One Case That Replaces Three Accessories

The Gorilla Cases Galaxy S23 Ultra Ring Holder Kickstand Case is a hybrid polycarbonate and TPU armor case for the Samsung Galaxy S23 Ultra that builds a magnetic ring holder, a metal kickstand, and a MagSafe compatible magnet array into a single shell, and it still charges wirelessly straight through the back. That one sentence is the whole pitch. Most ring cases force a trade: you get the grip and the stand, and you give up wireless charging because the ring sits dead center over the coil. This one does not make you choose. The magnet array is engineered around the charging zone, so you can drop the phone on a Qi pad or snap it onto a MagSafe puck without peeling anything off.

The Galaxy S23 Ultra is a 6.8 inch slab of glass that weighs 233 grams bare. It is a phone you drop. Not because you are careless, but because physics is not on your side when you are reaching for a coffee with one hand and holding a phone the size of a paperback in the other. The ring on the back of this case solves that in the simplest way possible: your index finger goes through it, and the phone is now physically attached to your hand. Flip the same ring out ninety degrees and it becomes a kickstand that holds the phone upright on a desk, a tray table, a kitchen counter, or a treadmill ledge.

Underneath the hardware, the shell itself is doing real work. A rigid polycarbonate frame takes the hard hits and keeps the case from flexing into the phone. A softer TPU layer lines the inside and wraps the corners, soaking up the shock that the hard shell transmits. The camera island sits behind a raised lip so the lens glass never touches the table. Every port, button, speaker grille, and microphone hole is cut open, including the S Pen silo. Welcome to the Gorilla Family.

Key Features and Benefits

• Built-in magnetic ring that still allows wireless charging: the magnet array is a ring, not a disc, so the center stays clear for the Qi coil. Set the phone on a wireless pad and it charges normally. This is the single biggest difference between this case and the older metal-plate car-mount cases that block charging entirely.
• MagSafe compatible magnet alignment: the ring snaps onto MagSafe chargers, MagSafe car mounts, magnetic wallets, magnetic tripod adapters, and magnetic power banks. The Galaxy S23 Ultra has no native magnets, so this case is what gives a Samsung flagship access to the entire magnetic accessory ecosystem.
• Metal ring holder kickstand: the ring is metal, not plastic, and it rotates through a full arc on a tensioned hinge. Use it as a finger loop for one-handed carrying, as a hook over a headrest, or fold it out as a stand for hands-free watching.
• PC plus TPU hybrid construction: premium polycarbonate on the outside for rigidity and abrasion resistance, flexible TPU on the inside for impact absorption. Shockproof, anti-drop, and built to stay structurally sound through daily abuse.
• Bump and impact protection across the back: the reinforced rear panel is designed to take bumps, knocks, and hard hits on the back panel, which is where the S23 Ultra is most vulnerable because it is almost entirely glass back there.
• Raised camera lip: a protective lip rises above the camera island so the 200 MP main sensor and the telephoto lenses never make contact when the phone is set face up on a flat surface.
• Full port and control access: open cutouts for the USB-C port, the volume rocker, the power button, the speaker, the microphone array, and the S Pen slot. Nothing is covered by a flap or a membrane.
• Textured armor styling: a machined, panel-line finish with contrasting ridges that reads as serious hardware rather than a generic slab, and gives your fingers something to hold onto.
• Black colorway: a deep matte black with darker accent detailing that hides scuffs, does not yellow the way clear cases do, and pairs with every phone finish Samsung sold.
• Galaxy S23 Ultra specific tooling: this case is molded for the Samsung Galaxy S23 Ultra only. It is not a universal shell with an approximate fit.

Materials Explained: What Polycarbonate, TPU, and Metal Actually Do Here

A case spec sheet that just says PC plus TPU does not tell you anything useful, so here is what those two materials actually contribute when your phone hits the ground.

Polycarbonate is the rigid outer shell. It is the same class of plastic used for a bicycle helmet shell. A helmet shell is hard not because hardness alone stops an impact, but because a hard outer layer spreads a concentrated hit across a wide area before it reaches the soft liner underneath. That is exactly the job polycarbonate does on this case. When a corner strikes concrete, the polycarbonate frame distributes that point load sideways through the shell instead of letting it punch straight into the phone frame. Polycarbonate also resists scratching and keeps its shape over time, so the case does not go floppy and start falling off after six months in a pocket.

TPU, thermoplastic polyurethane, is the flexible inner layer and the corner material. TPU is what the rim of a hockey puck is made from and what the midsole of a running shoe is made from. Both of those exist to convert a sharp impulse into a slower, softer one. A running shoe midsole does not stop your heel from hitting the sidewalk, it stretches the moment of contact out over more milliseconds so your joints feel less of it. The TPU in this case does the same thing for your phone: it compresses on impact and gives the energy somewhere to go that is not the display glass. TPU is also why the case grips your hand and your car cupholder instead of sliding around like bare polycarbonate would.

The third material is metal. The ring holder kickstand is metal, which is why it holds a viewing angle under the weight of a 233 gram phone instead of slowly sagging the way a plastic hinge does. The magnetic holder sheet built into the back is also metal, and that is the component that lets the case lock onto MagSafe chargers and magnetic mounts.

Weight and bulk stay reasonable. The packaged case weighs roughly 2 ounces, or 56 grams, which is about what a hybrid armor case with a metal ring should weigh. You will notice the ring more than you notice the shell.

Browse More Galaxy S23 Ultra Cases

Want to compare this ring kickstand design against wallet folios, clear cases, rugged armor, and slim shells before you commit? Browse the full Galaxy S23 Ultra cases collection and find the protective phone case that matches how you actually use your phone.

Real-World Use Cases

• The commuter, Dana: she rides the bus standing up with one hand on the rail. The ring goes over her index finger and the phone becomes an extension of her hand. No more death grip on a 6.8 inch phone while the bus brakes.
• The rideshare and delivery driver, Marcus: he snaps the phone onto a magnetic dash mount at every pickup and pulls it off at every drop. No adhesive plate glued to the case back, no cradle arms to fight with, and the phone charges on a MagSafe car charger while it sits there.
• The remote worker, Priya: ring flipped out, phone standing in landscape next to the laptop, running the team call on one screen while she works on the other. At the end of the day the same phone drops onto the Qi pad on her desk without the case coming off.
• The parent in the kitchen, Tom: recipe video propped on the counter in portrait, hands covered in flour, phone standing on its own at eye level instead of leaning against a canister and sliding down.
• The traveler, Elena: ring hooks over the seat-back tray latch on a flight, turning the phone into a seat-back screen. On the ground it clips onto a magnetic tripod adapter for steady photos.
• The gift buyer: one case that bundles a grip, a stand, a MagSafe adapter, and armor protection is a genuinely useful gift for anyone still carrying an S23 Ultra in a bare shell.

Feature to Benefit Mapping

Product Specs and Compatibility

• Compatible with: Samsung Galaxy S23 Ultra only. It does not fit the Galaxy S23, S23 Plus, S23 FE, S22 Ultra, S24 Ultra, or S25 Ultra. Check the model number on your phone before ordering.
• Materials: polycarbonate, TPU, and metal.
• Case features: built-in magnetic holder metal sheet plus ring holder kickstand.
• Color: Black.
• Wireless charging: supported. MagSafe compatible.
• Packaged weight: approximately 0.056 kg, or just under 2 ounces.
• Cutouts: USB-C port, volume buttons, power button, speaker, microphone, camera array, S Pen slot.
• In the box: one Galaxy S23 Ultra ring holder kickstand case. No other items are included.
• Not included and not claimed: this case does not include a screen protector, carries no IP water or dust resistance rating, and carries no certified drop-height rating.

Step-by-Step Installation Guide

1. Power the phone off or set it face down on a soft cloth, and wipe the back and sides with a microfiber cloth so no grit gets trapped between the phone and the TPU liner.
2. Hold the case with the camera cutout at the top and line it up with your camera island before you start pressing anything.
3. Seat the top edge of the phone into the top two corners of the case first. Let it drop in; do not force it.
4. Work down one side, then the other, pressing the TPU lip over the phone edge as you go.
5. Press the two bottom corners in last. You should feel the TPU snap over the frame.
6. Run a finger all the way around the perimeter to confirm the lip is seated everywhere and nothing is standing proud.
7. Test the volume rocker, the power button, the USB-C port with your own cable, and eject the S Pen once to confirm the slot cutout clears.
8. Fold the ring out and set the phone down in portrait, then in landscape, so you learn where the stable stop points are.
9. Place the phone on your wireless charger and confirm it starts charging, then snap it onto your magnetic mount and give it a gentle tug to confirm the hold.

Troubleshooting and Tips

• The ring hinge feels stiff out of the box. That is intentional. A loose hinge cannot hold a viewing angle. It loosens to a comfortable flip after the first week of use. Do not try to loosen it with tools.
• Wireless charging is slow or intermittent. Center the phone on the pad. The magnet ring leaves the coil zone clear, but an off-center placement on a narrow pad will still miss. If you use a thick charging pad with a raised rim, the ring may hold the case slightly off the surface; a flat pad works better.
• The magnetic mount hold feels weak. Align the mount head with the ring, not with the middle of the case. Magnetic force drops off fast with distance and offset, so a centered, flush contact is worth a lot more than a strong magnet placed badly.
• The phone tips over in landscape stand mode. Open the ring to its full stop and rest the bottom edge of the case on the surface so the ring and the case edge form a tripod. Half-open angles are the unstable ones.
• The ring rattles in your pocket. Rotate it flat into its recess. It sits flush when stowed.
• Cleaning. Mild soap and warm water on a cloth, then air dry fully before reinstalling. Skip alcohol wipes and solvents; they dry out TPU over time and dull the finish.
• Removing the case. Start at one bottom corner, peel the TPU lip outward and down, and the rest comes off easily. Never pry with a metal tool against the phone glass.
• Credit cards and hotel keys. The case contains magnets. Keep magnetic-stripe cards and hotel key cards away from the ring area, the same as you would with any MagSafe accessory.

Frequently Asked Questions

Yes, this case supports wireless charging. Does the Galaxy S23 Ultra Ring Holder Kickstand Case block Qi charging?
No. The magnet array is ring-shaped and leaves the center of the case back clear, so the Qi coil in your Galaxy S23 Ultra can reach the charging pad through the case. You do not need to remove the case to charge wirelessly.

Yes, it is MagSafe compatible. Will this case work with MagSafe chargers and magnetic accessories?
Yes. The built-in magnet ring is aligned to the MagSafe standard, so MagSafe chargers, magnetic car mounts, magnetic wallets, magnetic power banks, and magnetic tripod adapters all attach. The Galaxy S23 Ultra has no magnets of its own, so this case is what unlocks that accessory ecosystem for a Samsung phone.

It fits the Samsung Galaxy S23 Ultra only. Which phone models does this case fit?
This case is tooled specifically for the Samsung Galaxy S23 Ultra. It does not fit the Galaxy S23, the S23 Plus, the S23 FE, the S22 Ultra, the S24 Ultra, or the S25 Ultra. Confirm your model in Settings, About phone, before ordering.

One case, and nothing else. What comes in the box?
You receive one Galaxy S23 Ultra ring holder kickstand case in Black, with the magnet ring and the metal kickstand already built in. No other items are included. A screen protector, a charger, and a car mount are all sold separately.

Polycarbonate, TPU, and metal. What is this case made of?
The outer shell is polycarbonate, the rigid plastic used for bicycle helmet shells, which spreads impact force across the case. The inner layer and corners are TPU, the same flexible material used in hockey puck rims and running shoe midsoles, which absorbs shock. The ring holder kickstand and the magnetic holder sheet are metal.

Yes, both orientations work. Does the kickstand hold the phone in portrait and landscape?
Yes. The ring rotates on its hinge, so you can stand the Galaxy S23 Ultra upright in portrait for video calls and recipes, or sideways in landscape for movies and spreadsheets. Open the ring to its full stop for the most stable angle.

Yes, the S Pen works normally. Can I still use the S Pen with this case on?
Yes. The S Pen silo has a dedicated cutout, so you can eject and re-dock the pen without taking the case off the phone.

Yes, the fingerprint reader is unaffected. Does the in-display fingerprint sensor still work?
Yes. The case covers the back and the sides only. The Galaxy S23 Ultra ultrasonic in-display fingerprint reader sits under the screen and is completely unobstructed.

No, this case has no water resistance rating. Is it waterproof?
No. This case carries no IP rating and makes no water or dust resistance claim. Treat it as a protective shell against impact and abrasion only, and rely on your phone own factory water resistance for anything involving liquid.

No certified drop height is claimed. How much drop protection does it give?
The manufacturer describes this case as shockproof and anti-drop, built from premium PC plus TPU to protect against bumps, impacts, and hard hits on the back. No independent drop-test certification or specific drop-height rating is published for it, so we do not claim one.

Yes, the camera is protected by a raised lip. Will the lenses touch the table?
No. A raised lip surrounds the camera island and sits above the lens glass, so when you place the Galaxy S23 Ultra face up on a flat surface the 200 MP main camera and the telephoto lenses stay clear of it.

It is available in Black. What colors does this case come in?
Gorilla Cases stocks this Galaxy S23 Ultra ring holder kickstand case in Black. The matte black finish with darker accent detailing hides scuffs well and does not discolor the way clear cases do.

Yes, it is designed for one-handed use. Does the ring actually help with a phone this big?
Yes. The Galaxy S23 Ultra is a 6.8 inch phone that weighs 233 grams bare, which is a lot to balance on your fingertips. Putting your index finger through the ring means the phone is mechanically attached to your hand, so you are no longer relying on grip strength alone.

Yes, most slim tempered glass protectors fit alongside it. Can I use a screen protector with this case?
Yes. The case covers the back and the edges, and most standard tempered glass protectors for the Galaxy S23 Ultra sit within the curve of the screen without conflicting with the case lip. No screen protector is included with this case.

Call 978-797-0223 or email info@gorillacasestore.com. How do I reach Gorilla Cases with a question?
Our support line at 978-797-0223 is answered every day, and you can email info@gorillacasestore.com any time. Ask us about fitment, magnet strength, or which Galaxy S23 Ultra case suits your job before you order, and we will give you a straight answer.

Why Gorilla Cases

Gorilla Cases has been shipping phone protection since 2015 and has put more than 20,000 orders in customers hands. We build product pages the way we would want one written for us: we tell you what the case is made of, what it does, and just as importantly what it does not do. If a case has no IP rating, we say so. If nobody has drop-tested it to a certified height, we do not invent a number. If it does not come with a screen protector, you will read that here before you buy rather than discover it when the package arrives.

That honesty is the entire reason the Gorilla Family keeps coming back. Phone cases are a category drowning in invented specifications, and the fastest way to lose a customer forever is to promise armor and deliver a thin shell. We would rather undersell a good case than oversell a mediocre one.

Please read our policies before ordering, and if you are not certain this is the right case for your Galaxy S23 Ultra, call us first at 978-797-0223 and we will help you choose. Shop now at gorillacasestore.com and join the Gorilla Family.

Read More From the Gorilla Cases Blog

Still deciding how much protection you actually need? Read our guide to the Best Galaxy S23 Ultra Heavy Duty Case 2026, or start with the broader Galaxy S23 Ultra Cases overview for a tour of every case style that fits this phone.